Nylon 66 Radici injection molding grade, natural

Issued: 26/09/2016 www.radicigroup.com/plastics - info.plastics@radicigroup.com

The information provided in this documentation corresponds to knowledge of Radici Group Performance Plastics on the subject at the date of its publication. This information may be subject to revision as new

knowledge and experience become available. The data provided reflects the average values of the properties measured over an adequate number of different production cycles and relates only to the designated

material; this data may not be valid for such material used in combination with any other materials or additives or in any process, unless expressly indicated otherwise. The data provided should not be used to establish

specification limits nor used alone as the basis of design; it is not intended to substitute for any testing you may need to conduct to determine for yourself the suitability of a specific material for your particular

purposes. Since Radici Group Performance Plastics cannot anticipate all variations in actual end-use conditions Radici Group Performance Plastics makes no warranties and assumes no liability in connection with any

use of this information. Nothing in this publication is to be considered as a license to operate under or a recommendation to infringe any patent rights.

Page 1/ 2

PRODUCT INFORMATION

TORZEN T3000HS1L NC01

Material Code Colour Code

DESCRIPTION

PA66 injection moulding grade. Toughened, heat stabilized. Natural colour.

Suitable for parts requiring excellent impact resistance and improved surface appearance. Good properties

retention after ageing.

ISO 1043 : PA66-IT

MATERIAL HANDLING AND PROCESSING

The material is delivered in moisture-proof packaging ready for processing. Maximum recommended water

content for best processing is 0.15%. Typical conditions with a desiccant drier: temperature 80 ° C, dew

point -20 ° C or below, time 2-4 h or more.

Special care must be taken to avoid moisture absorption and contamination with other polymers when

adding regrind material. Colour variation and mechanical properties reduction may occur and should always

be carefully monitored.

Processing Parameters

Melt Temperature: Mold Temperature: Injection Speed:

270 ÷ 290 °C 70 ÷ 90 °C Medium

PRODUCT SAFETY AND APPROVALS

For safety instruction please refer to Material Safety Data Sheet

RoHS compliant 2011/65/UE and following amendments

Issued: 26/09/2016 www.radicigroup.com/plastics - info.plastics@radicigroup.com

The information provided in this documentation corresponds to knowledge of Radici Group Performance Plastics on the subject at the date of its publication. This information may be subject to revision as new

knowledge and experience become available. The data provided reflects the average values of the properties measured over an adequate number of different production cycles and relates only to the designated

material; this data may not be valid for such material used in combination with any other materials or additives or in any process, unless expressly indicated otherwise. The data provided should not be used to establish

specification limits nor used alone as the basis of design; it is not intended to substitute for any testing you may need to conduct to determine for yourself the suitability of a specific material for your particular

purposes. Since Radici Group Performance Plastics cannot anticipate all variations in actual end-use conditions Radici Group Performance Plastics makes no warranties and assumes no liability in connection with any

use of this information. Nothing in this publication is to be considered as a license to operate under or a recommendation to infringe any patent rights.

Page 2/ 2

TECHNICAL DATA SHEET

PROPERTY STANDARD UNIT VALUE

DAM* Cond**

Physical Properties

Density ISO 1183 Kg/m3 1070

Moulding shrinkage – Parallel / Normal //*** ISO 294-4 % 1,7-2,0 / 1,6-1,9

Mechanical Properties

Stress at Yield 50mm/min ISO 527-2/1A MPa 47

Yield Strain 50mm/min ISO 527-2/1A % 4,5

Nominal Strain at Break 50mm/min ISO 527-2/1A % 50

Flexural Modulus 2mm/min ISO 178 MPa 1900

Charpy Impact Strength +23°C ISO 179/1 eU kJ/m2 NB

Charpy Impact Strength -30°C ISO 179/1 eU kJ/m2 NB

Charpy Notched Impact Strength +23°C ISO 179/1 eA kJ/m2 82

Charpy Notched Impact Strength -40°C ISO 179/1 eA kJ/m2 19

Izod Notched Impact Strength -30°C ISO 180/1 eA kJ/m2 17

Thermal Properties

Melting Temperature 10°C/min ISO 11357-1-3  °C 262

Heat Deflection Temperature 1.8 MPa ISO 75/2 A f  °C 61

Heat Deflection Temperature 0.45 MPa ISO 75/2 B f  °C 148

*DAM = Dry As Moulded state **Cond = Conditioned state similar to ISO 1110 ***Melt Temp [°C] / Mold Temp [°C] / Cavity press [MPa]

TORZEN T3000HS1L NC01

Material Code Colour Code