Product Specification
March 2009
Product Aegis® H8202NLB
Product Description Aegis® H8202NLB is an unfilled, low/medium viscosity,
n ...
Read moreProduct Specification
March 2009
Product Aegis® H8202NLB
Product Description Aegis® H8202NLB is an unfilled, low/medium viscosity,
non-lubricated nylon 6 injection molding homopolymer
exhibiting excellent melt fluidity for filling thin sections. It
exhibits good strength, stiffness, and toughness as well
as excellent heat, chemical and abrasion resistance.
Specification:
Parameter Test Method Units Value
Viscosity, FAV ASTM D-789 49+/-3
%96 SAV 2.61
Moisture Content ASTM D-6869 % Max. 0.10
Extractable Content SOP-702-307 % Max. 0.8
General properties:
Physical Test Method Units Value
Specific Gravity ASTM D-792 sp gr 23/23°C 1.13
Mold Shrinkage linear Flow ASTM D-955 % 1.28
Rockwell Hardness, R Scale ASTM D-785 119
Moisture (24 Hour) ASTM D-570 % 1.6
Moisture (50% RH) ASTM D-570 % 2.7
Moisture (Saturation) ASTM D-570 % 9.5
Melt Flow Rate (235C, 1Kg) ASTM D-1238 g/10 min 9.8
Mechanical Test Method Units Value
Tensile Modulus, 23°C (73°F) ASTM D-638 MPa (psi) 2,850 (413,500)
Tensile Strength, Yield, 23°C (73°F) ASTM D-638 MPa (psi) 79 (11,500)
Elongation, Yield, 23°C (73°F) ASTM D-638 % 4.0
Elongation, Break, 23°C (73°F) ASTM D-638 % 55
Flexural Modulus, 23°C (73°F) ASTM D-790 MPa (psi) 3010 (436,000)
Flexural Strength, 23°C (73°F) ASTM D-790 MPa (psi) 110 (15,900)
Impact Test Method Units Value
Notched Izod impact -40°C (-40°F) ASTM D-256 J/M (ft-lbs/in) 50 (0.9)
Notched Izod impact 23°C (73°F) ASTM D-256 J/M (ft-lbs/in) 60 (1.1)
Thermal Test Method Units Value
Melting Point ASTM D-3418 °C (°F) 220 (428)
Heat Deflection @ 264 psi (1.8 MPa) ASTM D-648 °C (°F) 65 (149)
Heat Deflection @ 66 psi (0.45 MPa) ASTM D-648 °C (°F) 178 (352)
Coef. Of Linear Thermal Expansion ASTM E-831 μm/mm °C 83
Honeywell Resins and Chemicals
101 Columbia Road Morristown, NJ 07962
Customer Service Center: 1-866-495-3477
www.Honeywell-Plastics.com
Product handling
This product is supplied in sealed containers and drying prior to processing is not required.
However, high moisture is the primary cause of processing problems. If drying becomes
necessary a dehumidifying or desiccant dryer operating at 80 °C (176 °F) is recommended.
Drying time is dependent on moisture level. Further information concerning safe handling
procedures can be obtained from the Material Safety Data Sheet. Alternatively, please contact
your Honeywell representative.
Typical Profile
Melt Temperature 240-280 °C (464-536 °F)
Mold Temperature 80-95 °C (176-203 °F)
Injection and Packing Pressure 35-125 bar (500-1500 psi)
Mold Temperatures
A mold temperature of 80-95 °C (176-203 °F) is recommended, but temperatures as low as 10 C
(50 F) can be used where applicable.
Pressures
Injection pressure controls the filling of the part and should not be applied for 90% of ram travel.
Packing pressure affects the final part and can be used effectively in controlling sink marks and
shrinkage. It should be applied and maintained until the gate area is completely frozen off.
Fill Rate
Fast fill rates are recommended to insure uniform melt delivery to the cavity and prevent
premature freezing.
These values are for natural color resins only. Colorants or other additives may alter some or all
of these properties. The data listed here fall within the normal range of product properties, but
should not be used to establish specification limits nor used alone as the basis for design.
Disclaimer
Although all statements, information, and data given herein are believed to be accurate, they are
presented without guarantee, warranty, or responsibility of any kind, express or implied.
Statements or suggestions concerning possible use of our products are made without
representation or warranty that any such use is free of patent infringement, and are not
suggestions to infringe any patent. The user should not assume that all safety measures are
indicated, or that other measures may not be required. Further information concerning safe
handling procedures can be obtained from the Material Safety Data Sheet.
Honeywell Resins and Chemicals
101 Columbia Road Morristown, NJ 07962
Customer Service Center: 1-866-495-3477
www.Honeywell-Plastics.com
Show less